How to Make Angel Wings (with Pictures)

Table of contents:

How to Make Angel Wings (with Pictures)
How to Make Angel Wings (with Pictures)
Anonim

You can make simple angel wings even if you're short on time, on a budget, and modest manual skills. To create beautiful and resistant wings, simply reproduce the texture of feathers with paper plates or coffee filters.

Steps

Method 1 of 2: Wings with Paper Plates

Make Angel Wings Step 1
Make Angel Wings Step 1

Step 1. Draw a crescent moon on eight paper plates

Starting from the center of the top edge of a plate, draw a curved line to the bottom edge. You'll get a crescent-like section with a mostly jagged edge and some smooth parts. Repeat on the remaining dishes.

Make Angel Wings Step 2
Make Angel Wings Step 2

Step 2. Draw a second crescent moon on each plate

Being mirrored compared to the first, it must start and end in the same points. Between the two separate sections will remain a pointed oval shape, similar to a cat's iris.

Make Angel Wings Step 3
Make Angel Wings Step 3

Step 3. Cut along the lines

Set aside the cut out crescent moons that will act as feathers for your wings. The middle section of the plate should be discarded.

Make Angel Wings Step 4
Make Angel Wings Step 4

Step 4. Line up eight feathers along the side of an undamaged paper plate

Use common sense to arrange them so they form a graceful wing. In any case, remember that they should be placed close enough together.

Make Angel Wings Step 5
Make Angel Wings Step 5

Step 5. Imagine the plate is a clock

Starting from the left, the first feather should be placed between 10 and 11.

Make Angel Wings Step 6
Make Angel Wings Step 6

Step 6. After the first one, lay the other seven feathers one after the other, overlapping them slightly

Try to leave the upper feather almost completely hidden and the lower one clearly visible. The edge of each feather must be exposed, while the white center part is hidden by the next feather.

Make Angel Wings Step 7
Make Angel Wings Step 7

Step 7. Each feather should point downwards, however the corner of the top one should be slightly more open towards the outside, while the others that follow will gradually point downwards and inwards

Make Angel Wings Step 8
Make Angel Wings Step 8

Step 8. The last feather should be placed around 8 o'clock

Make Angel Wings Step 9
Make Angel Wings Step 9

Step 9. Repeat the placement process on the other side of the plate with the remaining feathers

Starting from the right, the top feather will be between 1 and 2, while the last will correspond to 4.

Make Angel Wings Step 10
Make Angel Wings Step 10

Step 10. Glue the feathers

When you are done, fix the feathers with glue. It can be helpful to make small marks with the marker so you can remember where each feather will be stuck. Apply a drop of hot glue to attach the feather to the base. Keep it pressed against the plate so that the glue sets.

Make Angel Wings Step 11
Make Angel Wings Step 11

Step 11. Attach a second plate on top of the first one to cover the base

Apply a thin strip of glue around the center of the base. The glue should be applied on the inside, where the tips of the feathers are visible. Compress the second plate on the first with the back facing out.

Make Angel Wings Step 12
Make Angel Wings Step 12

Step 12. Cut two long ribbons

They must be approximately 58 cm long, so that they can slide comfortably over the shoulders and arms of the wearer.

Make Angel Wings Step 13
Make Angel Wings Step 13

Step 13. Attach the ribbon to the center plate

The top should start at approximately the same point where the wings originate and the bottom end should be glued at the bottom where the wings end. Apply a drop of glue on both ends to make the tape adhere to the plate.

Make Angel Wings Step 14
Make Angel Wings Step 14

Step 14. Glue a plate to cover everything

To hide the ends of the ribbon and keep them in place, attach a third plate over the second. Spread the glue along the edges of the second and place the third over it while holding down.

Make Angel Wings Step 15
Make Angel Wings Step 15

Step 15. Let the glue dry

When the glue is dry, the wings can be worn.

Method 2 of 2: Wings with Coffee Filters

Make Angel Wings Step 16
Make Angel Wings Step 16

Step 1. Cut out a heart shape from card stock

The height of the heart will be that of the wings. You can choose the size you prefer, but generally it is worth considering the distance between the wearer's chin and the lower back. Make both sides of the heart as symmetrical as possible.

Make Angel Wings Step 17
Make Angel Wings Step 17

Step 2. Cut the heart in half

Make a precision cut from the center notch to the tip.

Make Angel Wings Step 18
Make Angel Wings Step 18

Step 3. Drill holes in the cardboard to put the braces

You may need to study the project a bit before cutting out the holes. If you're going to wear wings, get help or look in the mirror. Generally, the first hole can be made about 5 cm from the top edge and the second about 10 cm from the first. The holes for the other riser will be mirrored.

Make Angel Wings Step 19
Make Angel Wings Step 19

Step 4. Tie the shoelaces to the holes

You'll need four.

Make Angel Wings Step 20
Make Angel Wings Step 20

Step 5. The first snare connects both holes of one wing

The second lace passes through the holes in the second wing. Secure them tightly, leaving enough room for your arms to pass through.

Make Angel Wings Step 21
Make Angel Wings Step 21

Step 6. The third lace will connect the upper holes, the fourth lace will connect the two lower ones

Bind them keeping in mind that the wings must slide over your shoulders and that most of the cardboard will be visible from the front.

Make Angel Wings Step 22
Make Angel Wings Step 22

Step 7. Fold the coffee filters in half

The number of filters you need varies depending on the size of the wings, but you will need enough to cover the entire front and back area.

Make Angel Wings Step 23
Make Angel Wings Step 23

Step 8. Glue a row of filters along the inside of each wing

The inside corresponds to the straight line that divides the heart in half. Glue the filters on the front and back, so that the rounded edges rest on the cardboard on both sides.

Make Angel Wings Step 24
Make Angel Wings Step 24

Step 9. Layer the filters on both wings

Each layer should overlap slightly. The inside and outside should be half covered with filters but don't worry if some cardboard remains visible on the outside edge.

Make Angel Wings Step 25
Make Angel Wings Step 25

Step 10. Cover the outer edge of the wings

Starting at the bottom inside corner, place the filters on the edge so that half covers the outside and half the inside. Continue by lining up the filters along the outer edge of the wing, overlapping them until you reach the upper inner corner.

Make Angel Wings Step 26
Make Angel Wings Step 26

Step 11. Cover the laces

Theoretically, the excess of the filters will have already covered the laces that connect the two wings. If not, you can use other filters on the top by gluing them to the laces.

Recommended: