4 Ways to Replace a Bathroom Faucet

Table of contents:

4 Ways to Replace a Bathroom Faucet
4 Ways to Replace a Bathroom Faucet
Anonim

A new faucet can give your bathroom a decidedly new look with minimal effort and low cost. This job takes only a few hours and can easily be done in a weekend.

Steps

Method 1 of 4: Part 1: Install the Barrel

Replace a Bathroom Faucet Step 1
Replace a Bathroom Faucet Step 1

Step 1. Measure the distance between the sink holes where the handles fit, with a tape measure or ruler, to evaluate the type of faucet to buy

Replace a Bathroom Faucet Step 2
Replace a Bathroom Faucet Step 2

Step 2. Close the hot and cold water valves under the sink

Replace a Bathroom Faucet Step 3
Replace a Bathroom Faucet Step 3

Step 3. Remove the old faucet by unscrewing the screws that secure it to the sink

You will find the screw under the decorative cover, at the top of the faucet.

Replace a Bathroom Faucet Step 4
Replace a Bathroom Faucet Step 4

Step 4. Unscrew the metal circle located under the sink

Replace a Bathroom Faucet Step 5
Replace a Bathroom Faucet Step 5

Step 5. Insert the new spout into the center of the sink drain hole

Insert a washer into the top of the barrel and screw the nut to hold it in place.

Replace a Bathroom Faucet Step 6
Replace a Bathroom Faucet Step 6

Step 6. Screw the nut by hand

Replace a Bathroom Faucet Step 7
Replace a Bathroom Faucet Step 7

Step 7. Insert the three-way joint into the bottom of the barrel

Line it up with the hot and cold water valves, and secure it in place.

Method 2 of 4: Part 2: Connect the Hot and Cold Water Valves

Replace a Bathroom Faucet Step 8
Replace a Bathroom Faucet Step 8

Step 1. Insert the hot and cold water valves into the designated holes

Replace a Bathroom Faucet Step 9
Replace a Bathroom Faucet Step 9

Step 2. Secure the valve nut under the sink

Replace a Bathroom Faucet Step 10
Replace a Bathroom Faucet Step 10

Step 3. Connect the rosette at the top

Replace a Bathroom Faucet Step 11
Replace a Bathroom Faucet Step 11

Step 4. Connect the hot and cold water pipes to the valves

Replace a Bathroom Faucet Step 12
Replace a Bathroom Faucet Step 12

Step 5. Connect the other ends of the braided hoses to the three-way joint

Replace a Bathroom Faucet Step 13
Replace a Bathroom Faucet Step 13

Step 6. Tighten the nuts on all four ends

Replace a Bathroom Faucet Step 14
Replace a Bathroom Faucet Step 14

Step 7. Place the faucet handles on the valves

They should face inward when open and outward when closed.

Replace a Bathroom Faucet Step 15
Replace a Bathroom Faucet Step 15

Step 8. Connect the supply line to the hot and cold water valves and shut-off valve

Method 3 of 4: Part 4: Install the Exhaust Manifold

Replace a Bathroom Faucet Step 16
Replace a Bathroom Faucet Step 16

Step 1. Remove the drain manifold, spigot and rim from under the sink by removing the nuts

Replace a Bathroom Faucet Step 17
Replace a Bathroom Faucet Step 17

Step 2. Apply silicone to the new exhaust manifold and insert it into the hole provided

Replace a Bathroom Faucet Step 18
Replace a Bathroom Faucet Step 18

Step 3. Screw the rim onto the manifold

Replace a Bathroom Faucet Step 19
Replace a Bathroom Faucet Step 19

Step 4. Tighten the nut from under the sink

Replace a Bathroom Faucet Step 20
Replace a Bathroom Faucet Step 20

Step 5. Connect the old tang to the exhaust rim and replace the manifold

Method 4 of 4: Part 5: Install the Drain Plug

The drain plug consists of a connecting rod connected to a metal belt; a rod with a ball is attached to the strap. The ball is placed in the drain to control the movement of the cap.

Replace a Bathroom Faucet Step 21
Replace a Bathroom Faucet Step 21

Step 1. Place a washer, nut and spring clip on the ball rod

The rod is fixed to the connecting rod and has a sphere on one end.

Replace a Bathroom Faucet Step 22
Replace a Bathroom Faucet Step 22

Step 2. Place the rod in one of the holes in the strap and insert an elastic clip over it

Replace a Bathroom Faucet Step 23
Replace a Bathroom Faucet Step 23

Step 3. Put a washer on the other end of the rod and insert the ball into the rim

Replace a Bathroom Faucet Step 24
Replace a Bathroom Faucet Step 24

Step 4. Hold the stopper in the drain and use the rod to grab the hook

Replace a Bathroom Faucet Step 25
Replace a Bathroom Faucet Step 25

Step 5. Secure a nut on the exhaust tailpiece, but so that it is not too tight and the ball can move

Replace a Bathroom Faucet Step 26
Replace a Bathroom Faucet Step 26

Step 6. Insert the connecting rod through the barrel into the belt

Replace a Bathroom Faucet Step 27
Replace a Bathroom Faucet Step 27

Step 7. Open the water valve

Advice

  • Remove the aerator to clean the implant before using it.
  • When removing the old faucet, use anti-rust oil if the nuts are rusted.

Recommended: