The Gorilla glue that guarantees an extra strong long-lasting hold has finally arrived in Italy. Creates a fastener that resists water damage and sudden changes in temperature. However, it requires extreme attention at the time of use, since it is not at all easy to remove it from the skin or surfaces. If you haven't been careful enough, the first thing to do is moisten the glue with water, citrus juice, or acetone. Once wet, try scratching it off or peeling it off like an adhesive with a putty knife or toothbrush. After repeating this process a few times, the glue should come off easier.
Steps
Method 1 of 3: Remove the Glue from the Skin
Step 1. Wash the glue-stained area with soap and water
Pour half a liter of hot water into a basin and add a tablespoon (15 ml) of dish soap. Dip the glue-stained part into the water and soak it for at least 5 minutes. Then empty the bowl, fill it with clean hot water and detergent, then repeat the procedure at least one more time. This way the glue should begin to melt.
Step 2. Use the juice of a citrus fruit
Pour a few drops of lemon or lime directly onto the glue-stained skin. Alternatively, you can cut a lemon in half and keep it in contact with the skin for 5 minutes. Citric acid will begin to corrode the glue, which will then come off more easily.
If you have cuts or grazes on your skin, they may become irritated and you may feel a severe burning, so be careful if you decide to use citrus juice
Step 3. Use acetone based nail polish remover
Moisten a cotton swab or cotton swab. If the glue-stained area of skin is large, you can pour some solvent into a basin and soak the part for 6-10 minutes. When finished, rinse your skin with plenty of warm water and wash it with a mild soap.
Make sure the solvent contains a high percentage of acetone, as that is the ingredient that will corrode the glue
Step 4. Exfoliate the skin with the pumice stone
Hold the stone firmly in one hand and rub it back and forth over the glue residue. Apply enough pressure to scrape off the glue, but not so intense that it will tear or injure the skin. Continue scrubbing for a few minutes, until the glue begins to peel off the skin.
- Change direction with each step of the pumice stone to minimize skin damage.
- Alternatively, you can try using exfoliating gloves to peel the glue off the skin.
Step 5. Exfoliate your skin with sugar and salt
Mix 1 tablespoon of sugar and 1 tablespoon of salt in a bowl, then add enough water to moisten both. Apply the mixture to the glue-stained skin and scrub the area with your fingers. When the salt and sugar have dissolved, remove them and repeat. Being rough, the sugar and salt crystals should be able to gradually scrape the glue off the skin.
Step 6. Massage the skin with the warm oil
Pour a small amount of olive, sunflower, coconut, or baby oil into a bowl and heat it in the microwave for 10-20 seconds. It must be hot, not hot. Dip a cotton swab into the oil and apply it directly to the glue residue. Let it sit for 3-4 minutes, then check if the glue has dissolved. If not, repeat the whole process from the beginning.
According to some reports, even non-heated lip gloss and non-stick cooking spray can help loosen super glue
Step 7. Wait for the glue to come off by itself
The skin regrows and regenerates in a natural way. If the stained area isn't very large and you don't feel pain, you can simply wait for the glue to crumble on its own in 5-6 days, especially if you don't want to apply corrosive chemicals to your skin. Check that the skin around it does not tear or crack.
Step 8. Apply a moisturizer to clean skin
The glue creates a barrier that insulates the skin from moisture - this effect, combined with that of the chemicals you used to dissolve it, can make skin unusually dry or cracked. Apply a cream or oil to counteract the dehydrating action of glue and chemicals.
Step 9. Don't try to hastily separate the skin flaps
Resist the temptation to pull the glue to detach it from the skin it adheres to. Gorilla glue has an ultra strong action and can cause major damage to the skin. If the affected area is large or if you feel pain, see a doctor immediately.
Method 2 of 3: Remove Glue from Other Surfaces
Step 1. Give it a try
Locate a generally inconspicuous spot on the damaged surface. Dip a cotton ball in the chemical you intend to use to remove the glue, place it on the surface to be cleaned and let the product sit for 5 minutes. Remove the cotton ball and observe the material to see if it is damaged or discolored. It is important to perform this simple test to know if the chemical you have selected can be used without contraindications over a larger area.
Step 2. Use acetone
You can use 100% pure acetone to remove Gorilla Glue from fabrics or hard surfaces. Take a cotton ball and dip it in the acetone, then place it on the stained surface and let the solvent work for 5 minutes. Remove the cotton ball and wipe the surface to be cleaned with a damp rag. Repeat the process if there are still some glue residues left.
Do not use acetone on plastic surfaces as it may damage them further
Step 3. Use denatured alcohol on metal and non-plastic materials
Dampen a cotton ball or paper towel and place it on the glue-stained area. Let the alcohol sit for about 5 minutes, then clean the surface with warm soapy water. The glue should loosen and you should be able to scrape it off with a putty knife.
Step 4. Remove the glue with a thin flat tool if a hard surface is stained
Take a putty knife or other similar tool and push the glue to the side. Try to lift the edges of the glue layer with gentle movements to be able to peel it off as if it were an adhesive. If this fails, you can apply a small amount of acetone to the area with a cotton ball and then try again.
Step 5. Scrub the tissues with a toothbrush
Apply a few drops of acetone or detergent and water to the stained fabric. Take a toothbrush and scrub the bristles into the glue. Try to move them in always different directions, plus try gently tapping the fabric to crumble the glue.
Step 6. Wash stained clothing or fabrics
After removing most of the glue residue from the surface of the fabric, put the garment in the washing machine and wash it alone at the highest possible temperature. Read the label with washing instructions to avoid damaging it.
To avoid making the situation worse, it is best to wait until the glue is completely dry before putting the stained garment or garment in the washing machine
Step 7. If the stained surface is plastic, spread a wet cloth over it
If the glue has landed on a plastic object, removing it can be very difficult, as acetone and alcohol tend to corrode the surface. Wet a cotton rag in warm soapy water and leave it on the glue-stained area for 2-4 hours. From time to time, pour a little soapy water on the cloth to keep it moist.
Wipe the surface with a clean rag to remove any glue residue. If they don't come off, gently scrub the surface with a toothbrush
Method 3 of 3: Usage Precautions for Gorilla Glue
Step 1. Follow the instructions on the package
Before starting your project, carefully read the instructions for use on the Gorilla glue package. Pay particular attention to the directions on how to hold the applicator and the dosage. If in doubt, contact the manufacturer's customer service or consult the website.
For example, to get the glue down to the opening, you will need to turn the bottle upside down and tap the cap on a hard surface a couple of times
Step 2. Use gloves
The best thing to do is to put on a pair of work gloves before opening the package of glue to protect the skin on your hands. Try different types of gloves on sale and choose the most comfortable ones. However, try to be careful to avoid staining them.
Disposable gloves are very handy when you have to work with glue, but you have to make sure they are the right size
Step 3. Cover your work surface
Move unneeded items and line the entire area with cling film or aluminum foil. The latter is to be preferred since, once hardened, the glue does not stick to the aluminum. In both cases, the coating will protect the underlying surface, for example the kitchen counter, and prevent it from being damaged.
Step 4. Choose the right applicator for your project
One of the biggest mistakes you can make is trying to complete a project using an applicator that is too large or too small. Gorilla Glue is sold in different formats, for example in a tube or with a pen applicator, so do your research to choose exactly what you need.
